 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| UFR1610 THRU UFR1660 Features * Plastic package has Underwriters Laboratory Flammability Classification 94V-0 * Low forward voltage drop * High current capability * High reliability * Low power loss, high effciency * High surge current capability * High speed switching * Low leakage 0. 2 CURRENT 16.0 Amperes VOLTAGE 50 to 600 Volts ITO-220 10 0.5 3.2 0.2 0.1 4.5 0.2 6.4 0.1 2.7 0.2 2.7 0.2 3.7 Mechanical Data * Case : JEDEC ITO-220 molded plastic body * Terminals : Lead solderable per MIL-STD-750, method 2026 * Polarity : As marked * Mounting Position : Any * Weight : 0.08 ounce, 2.24 gram 2.54 0.2 0.7 2.54 0.2 0.2 13Min 1.3 0.2 15 0.3 0.5 2.4 PIN 1 PIN 3 Negative CT Suffix "A" 0.2 0.2 PIN 1 PIN 3 Positive CT Suffix "C" + CASE PIN 2 CASE PIN 2 Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25E ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols Maximum recurrent peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current 0.375"(9.5mm) lead length @ at TA=100E Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) Maximum instantaneous forward voltage at 8.0A Maximum DC reverse current at rated DC blocking voltage TA=25E Maximum DC reverse current at rated DC blocking voltage TA=125E Maximum reverse recovery time (Note 1) Typical junction capacitance (Note 2) Typical thermal resistance (Note 3) Operating junction and storage temperature range IR VRRM VRMS VDC I(AV) IFSM VF UFR 1610 100 70 100 UFR 1620 200 140 200 UFR 1630 300 210 300 UFR 1640 400 280 400 16.0 200 UFR 1650 500 350 500 UFR 1660 600 420 600 Units Volts Volts Volts Amps Amps 1.0 10.0 1.3 1.7 Volts iA 100 Trr CJ 50 80 2.2 -55 to +150 -55 to +150 80 50 ns pF E /W E Re JC TJ TSTG Notes: (1) Test conditions: IF=0.5A, IR=1.0A, Irr=0.25A. (2) Measured at 1MHz and applied reverse voltage of 4.0 Volts. (3) Thermal resistance from junction to case mounting on heatsink. RATINGS AND CHARACTERISTIC CURVES UFR1610 THRU UFR1660 FIG . 1 -REVERSE RECOVERY TIME CHARACTERISTIC NONINDUCTIVE 50 NONINDUCTIVE 10 AND TEST CIRCUIT DIAGRAM trr +0.5A PULSE GENERATOR ( NOTE 2 ) 0 -0.25A DUT (+ ) 50Vdc (approx) (-) NONINDUCTIVE OSCILLOSCOPE (NOTE 2 ) -1.0A 1cm SET TIME BASE FOR 5/ 10ns / cm NOTES: 1 . RISE TIME = 7nsmax. INPUT IMPEDANCE= 1 MEGOHM 22p 2 . RISE TIME = 10ns max. SOURSE IMPEDANCE = 50ohmsf AVERAGE FORWARD CURRENT . ( A ) . FIG 2 -MAXIMUM AVERAGE FORWARD CURRENT DERATING 20 16 12 8 4 0 0 50 100 CASE TEMPERATURE . ( % ) 150 A) 1000 FIG . 3 -TYPICAL REVERSE CHARACTERISTICS INSTANTAN EOUS REVERSE CURRET . ( 100 Tj=125 C O 10 Tj=25 C O PE A K F O R W A R D S U R G E C U R R E N T . ( A ) FIG . 4 -MAXIMUM NON - REPETITIVE FORWARD SURGE CURRENT 120 90 60 1 Tj=25 C o 8.3ms Single Half Sine Wave JEDEC Method 0.1 PERCENT OF RATED PEAK REVERSE VOLT AGE . (%) 20 40 60 80 100 120 140 INSTANTANEOUS FORWARD CURRENT . ( A) 30 1 2 5 10 20 NMBER OF CYCLES AT 60Hz 50 1 00 FIG . 6 -TYPICAL FRWARD CHARACTERISTICS 100 30 64 0-1 240 CAPACITANCE ( pF) 200 160 120 80 40 0 FIG . 5 -TYPICAL JUNCTIOON CAP ACITANCE PER LEG 1.0 0.3 0.1 0.03 .010.4 UF R1 3.0 61 UF UF R1 66 R1 Tj=25oC Pulse Width=300 1% Duty Cycle 0 Tj=25 C o UF UF R1 66 0 R1 61 0-1 65 0 65 10 0 0 s 1.8 0.6 0.8 1.0 1.2 1.4 1.6 1 2 5 10 20 50 100 200 REVERSE VOLTAGE . ( V) 500 1000 FORWARD VOLTAGE . ( V ) |
Price & Availability of UFR1660
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |